Williams Form Engineering Corp. Williams Form Engineering Corp.
Williams Form Engineering Corp.
DownloadsDownloadsWhat's NewContact UsAbout UsWilliams Form Engineering Corp.
Ground Anchor Systems
Concrete Anchor Systems
Post Tensioning Systems
Threaded Bars with Fasteners
Tie Rods & Tie Backs
Micro Piles
Concrete Forming Hardware Systems
Williams products are made in the USA

Cast-in-Place Anchor Installation Equipment

Cast-in-Place
Information
Parts &
Accessories
Installation
Equipment
Case
Histories
Corrosion
Protection
Hydraulic Jacks Post-Tensioning Jacks
Hydraulic Torque Wrench Manual Torque Wrench
Torque Wrench Multiplier Long Fitting Tool Adapters
Long Fitting Wrench Adapters Hex Knocker Wrench
T7Z Hydraulic Jacks Hydraulic Jack

Used for testing and pre-stressing anchor bolts. Available with up to 5-1/8" center hole. Unit comes with ram, pump, gauge, hoses, jack stand, high strength coupling, high strength test rod, plate, hex nut and knocker wrench. Calibrations are available upon request.

Note: Jack pull rods should have a higher capacity than the anchor rod.

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total
Height
of Ram
& Frame
Maximum
Test Rod
Diameter
Ram
Area
Approx.
Total
Weight
of Ram
& Frame
10 tons
(89 kN)
Hand
Single Acting
5-5/16"
(135 mm)
3" Dia.
(76 mm)
2-1/2"
(64 mm)
8-3/8"
(213 mm)
3/4"
(19 mm)
2.12 in2
(1368 mm2)
12 lbs.
(5.4 kg)

30 tons
(267 kN)

Hand
Single Acting

6-1/16"
(154 mm)

8" x 8"
(203 x 203 mm)

3"
(76 mm)

19"
(483 mm)

1-1/4"
(32 mm)

5.89 in2
(3800 mm2)

80 lbs.
(36 kg)

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

9-1/2"
(241 mm)

8" x 8"
(203 x 203 mm)

5"
(127 mm)

29"
(737 mm)

2"
(51 mm)

12.31 in2
(7942 mm2)

153 lbs.
(69 kg)

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

12-3/4"
(324 mm)

9" x 9"
(228 x 228 mm)

6-1/2"
(165 mm)

29"
(737 mm)

2"
(51 mm)

12.73 in2
(8213 mm2)

225 lbs.
(102 kg)

100 tons
(890 kN)

Air or Electric
Double Acting

13-1/2"
(343 mm)

9" x 9"
(228 x 228 mm)

6"
(152 mm)

35"
(889 mm)

3-1/8"
(79 mm)

20.63 in2
(13310 mm2)

270 lbs.
(123 kg)

100 tons
(890 kN)
Air or Electric
Double Acting

12-3/8"
(314 mm)

9" x 9"
(228 x 228 mm)

6"
(152 mm)

28"
(711 mm)

2"
(51 mm)

20.03 in2
(12923 mm2)

192 lbs.
(87 kg)

150 tons
(1334 kN)

Air or Electric
Double Acting

12-1/4"
(311 mm)

12" x 12"
(305 x 305 mm)

5"
(127 mm)

32-1/4"
(819 mm)

2-1/2"
(64 mm)

30.1 in2
(19419 mm2)

350 lbs.
(159 kg)

200 tons
(1779 kN)

Air or Electric
Double Acting

16"
(406 mm)

12" x 12"
(305 x 305 mm)

8"
(203 mm)

34"
(864 mm)

4"
(102 mm)

40.45 in2
(26097 mm2)

518 lbs.
(235 kg)

400 tons
(3558 kN)

Electric
Double Acting

18-3/4"
(476 mm)

15" Dia.
(381 mm)

6"
(152 mm)

45-3/4"
(1162 mm)

4-1/4"
(108 mm)

91.5 in2
(59032 mm2)

1300 lbs.
(590 kg)

400 tons
(3558 kN)
Electric
Double Acting

20-3/8"
(518 mm)

17" Dia.
(432 mm)

8"
(203 mm)

49"
(1245 mm)

5"
(127 mm)

118 in2
(76258 mm2)

1500 lbs.
(680 kg)

Certification of gauge accuracy available on request prior to shipment only.
Hydraulic Jack Detail

T80 Post-Tensioning Jacks

Post-Tensioning Jack

With the T80 series the enclosed bearing housing contains a geared socket drive to tighten the bolt hex nut during tensioning. Test jack housing will accommodate up to a 9” deep pocket.

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total
Height
of Ram
& Frame
Maximum
Test Rod
Diameter
Ram
Area
Approx.
Total
Weight
of Ram
& Frame

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

9-1/2"
(241 mm)

Gear Box: 6.5" x 9.5"
(165 x 241 mm)
Cylinder Dia.: 3.63"
(92 mm)

5"
(127 mm)

30"
(762 mm)

2"
(51 mm)

12.31 in2
(7942 mm2)

122 lbs.
(55 kg)

100 tons
(890 kN)

Air or Electric
Double Acting

13-1/2"
(343 mm)

Gear Box: 8.5" x 12"
(216 x 305 mm)
Cylinder Dia.: 4.63"
(118 mm)

6"
(152 mm)

25"
(635 mm)

3-1/8"
(79 mm)

20.63 in2
(13310 mm2)

270 lbs.
(123 kg)

150 tons
(1334 kN)

Air or Electric
Double Acting

12-1/4"
(311 mm)

5"
(127 mm)

24"
(610 mm)

2-1/2"
(64 mm)

30.1 in2
(19419 mm2)

243 lbs.
(110 kg)

200 tons
(1779 kN)

Air or Electric
Double Acting

16"
(406 mm)

Frame: 11" x 11"
(305 x 305 mm)
Nose: 7" Dia.
(178 mm)

8"
(203 mm)

37"
(940 mm)

4"
(102 mm)

40.45 in2
(26097 mm2)

455 lbs.
(203 kg)

T8Z-18 Hydraulic Torque Wrench Hydraulic Torque Wrench
The hydraulic torque wrench is used for tensioning anchors in tight fitting locations where it would be difficult to use an hydraulic jack. The wrench is also recommended for use when setting the large diameter Spin-Lock anchors. The torque wrenches are light weight and can achieve a maximum of 8,000 ft-lbs. Torque Tensioning charts Williams products can be found here.
Maximum
Torque
Length Height Weight
5,590 ft./lbs.
(773 kg/M)
11.11"
(279 mm)
4.49"
(114 kg)
16.75 lbs.
(7.6 kg)
8,000 ft.lbs.
(1,006 kg/M)
12.57"
(319 kg)
5.09"
(129 kg)
24.95 lbs.
(11.3 kg)
T8Z Torque Wrench

For applying torque to the anchor bolt when setting the anchor. Torque Tensioning charts Williams products can be found here.

Bolt
Diameter
Square
Drive Size
Capacity
(ft. lbs.)
*1/2"-1" 3/4" 0-500
1/2"-1" 3/4" 0-600
*1-1/8"-2" 1" 0-1,000
*Available with Ratchet Adapter
Torque Wrench
T8Z-04 Torque Multiplier (4:1)

For use with T8Z Torque Wrench. Other sizes available.

Torque Multiplier
Size Square Drive
Input
Square Drive
Output
Maximum
Torque
GA 186 1" 1-1/2" 4,000 (ft. lbs.)
T1Z & T2Z Long Fitting Tool Adapters

For driving hex nuts and setting tools, typically with our Spin-Lock anchor systems. Works with torque wrench or impact gun.
Available with 1" or 1-1/2" square drive. Please specify square drive for compatibility with your equipment.

Long Fitting Tool Adapter - Regular Socket
T2Z Regular Socket
Long Fitting Tool Adapter - Deep Socket
T1Z Deep Socket
K3F-26 Long Fitting Wrench Adapter

For applying torque to recessed anchor nuts that are under tension when using hydraulic jacks. Available in all anchor sizes.

Long Fitting Wrench Adapter
T3Z Hex Knocker Wrench

Used for safe hex nut adjustment inside of open frame jacks.

Knocker Wrench
Williams Form Engineering Corp.
Cast-in-Place
Information
Parts &
Accessories
Installation
Equipment
Case
Histories
Corrosion
Protection
Contact Us Home
Williams Form Engineering Corp. All rights reserved.