Williams Form Engineering Corp. Williams Form Engineering Corp.
Williams Form Engineering Corp.
DownloadsDownloadsWhat's NewContact UsAbout UsWilliams Form Engineering Corp.
Ground Anchor Systems
Concrete Anchor Systems
Post Tensioning Systems
Threaded Bars with Fasteners
Tie Rods & Tie Backs
Micro Piles
Concrete Forming Hardware Systems
Williams products are made in the USA

Post Tensioning Installation Equipment

Post Tension
Information
Parts &
Accessories
Post Tension
Installation
Installation Equipment Case
Histories
Corrosion
Protection
Air Powered Grout Pump Colloidal Grout Plant
Hydraulic Jacks Post-Tensioning Jacks
Hydraulic Torque Wrench Manual Torque Wrench
Torque Wrench Multiplier Long Fitting Tool Adapters
Long Fitting Wrench Adapters
T6Z-08 Air Powered Grout Pump
T6Z-02 Air Powered Grout Pump
Pumps cement grout only, no sand. 32 Gallon Mixing Tank. Mixes up to 2 sacks of material at once and allows for grout to be pumped during mixing or mixed without pumping.
Approximate size: 50" long
30.5" high
52" wide
Weight: 560 lbs.
Production Rate: 8 gallons per minute
at 150 psi

Colloidal Grout Plant
Colloidal Grout Plant
The heavy duty, high volume Colloidal Grout Plant is favored for precision post-tension grouting. The unit features a high speed shear mixer that thoroughly wets each particle and discharges the mixed material into a 13 cubic foot capacity agitating holding tank. A direct coupled progressing cavity pump delivers slurries at a rate of up to 20 gpm and pressures of up to 261 psi. The unit easily mixes and pumps slurries of Portland cement, fly ash, bentonite, and lime flour. All controls are conveniently located on the operator platform for easy one-man control.
Pump Pump Type 31.6 progressing cavity
Output/Preasure variable up to 20 gpm, 261 psi
Colloidal Mixer Mix Tank 13.0 CF with bottom clean out
Mixing Pump 2 x 3 x 6 diffuser-type centrifugal
Holding Tank 13.0 paddle agitating
Drive Power Air 300 CFM, 100 psi
Physical Specifications Dimensions 96" L x 60" W x 63" H
Weight 1800-2800 lbs.
T7Z Hydraulic Jacks Hydraulic Jack

Used for testing and pre-stressing anchor bolts. Available with up to 5-1/8" center hole. Unit comes with ram, pump, gauge, hoses, jack stand, high strength coupling, high strength test rod, plate, hex nut and knocker wrench. Calibrations are available upon request.

Note: Jack pull rods should have a higher capacity than the anchor rod.

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total
Height
of Ram
& Frame
Maximum
Test Rod
Diameter
Ram
Area
Approx.
Total
Weight
of Ram
& Frame
10 tons
(89 kN)
Hand
Single Acting
5-5/16"
(135 mm)
3" Dia.
(76 mm)
2-1/2"
(64 mm)
8-3/8"
(213 mm)
3/4"
(19 mm)
2.12 in2
(1368 mm2)
12 lbs.
(5.4 kg)

30 tons
(267 kN)

Hand
Single Acting

6-1/16"
(154 mm)

8" x 8"
(203 x 203 mm)

3"
(76 mm)

19"
(483 mm)

1-1/4"
(32 mm)

5.89 in2
(3800 mm2)

80 lbs.
(36 kg)

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

9-1/2"
(241 mm)

8" x 8"
(203 x 203 mm)

5"
(127 mm)

29"
(737 mm)

2"
(51 mm)

12.31 in2
(7942 mm2)

153 lbs.
(69 kg)

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

12-3/4"
(324 mm)

9" x 9"
(228 x 228 mm)

6-1/2"
(165 mm)

29"
(737 mm)

2"
(51 mm)

12.73 in2
(8213 mm2)

225 lbs.
(102 kg)

100 tons
(890 kN)

Air or Electric
Double Acting

13-1/2"
(343 mm)

9" x 9"
(228 x 228 mm)

6"
(152 mm)

35"
(889 mm)

3-1/8"
(79 mm)

20.63 in2
(13310 mm2)

270 lbs.
(123 kg)

100 tons
(890 kN)
Air or Electric
Double Acting

12-3/8"
(314 mm)

9" x 9"
(228 x 228 mm)

6"
(152 mm)

28"
(711 mm)

2"
(51 mm)

20.03 in2
(12923 mm2)

192 lbs.
(87 kg)

150 tons
(1334 kN)

Air or Electric
Double Acting

12-1/4"
(311 mm)

12" x 12"
(305 x 305 mm)

5"
(127 mm)

32-1/4"
(819 mm)

2-1/2"
(64 mm)

30.1 in2
(19419 mm2)

350 lbs.
(159 kg)

200 tons
(1779 kN)

Air or Electric
Double Acting

16"
(406 mm)

12" x 12"
(305 x 305 mm)

8"
(203 mm)

34"
(864 mm)

4"
(102 mm)

40.45 in2
(26097 mm2)

518 lbs.
(235 kg)

400 tons
(3558 kN)

Electric
Double Acting

18-3/4"
(476 mm)

15" Dia.
(381 mm)

6"
(152 mm)

45-3/4"
(1162 mm)

4-1/4"
(108 mm)

91.5 in2
(59032 mm2)

1300 lbs.
(590 kg)

400 tons
(3558 kN)
Electric
Double Acting

20-3/8"
(518 mm)

17" Dia.
(432 mm)

8"
(203 mm)

49"
(1245 mm)

5"
(127 mm)

118 in2
(76258 mm2)

1500 lbs.
(680 kg)

Certification of gauge accuracy available on request prior to shipment only.
Hydraulic Jack Detail

T80 Post-Tensioning Jacks

Post-Tensioning Jack

With the T80 series the enclosed bearing housing contains a geared socket drive to tighten the bolt hex nut during tensioning. Test jack housing will accommodate up to a 9” deep pocket.

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total
Height
of Ram
& Frame
Maximum
Test Rod
Diameter
Ram
Area
Approx.
Total
Weight
of Ram
& Frame

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

9-1/2"
(241 mm)

Gear Box: 6.5" x 9.5"
(165 x 241 mm)
Cylinder Dia.: 3.63"
(92 mm)

5"
(127 mm)

30"
(762 mm)

2"
(51 mm)

12.31 in2
(7942 mm2)

122 lbs.
(55 kg)

100 tons
(890 kN)

Air or Electric
Double Acting

13-1/2"
(343 mm)

Gear Box: 8.5" x 12"
(216 x 305 mm)
Cylinder Dia.: 4.63"
(118 mm)

6"
(152 mm)

25"
(635 mm)

3-1/8"
(79 mm)

20.63 in2
(13310 mm2)

270 lbs.
(123 kg)

150 tons
(1334 kN)

Air or Electric
Double Acting

12-1/4"
(311 mm)

5"
(127 mm)

24"
(610 mm)

2-1/2"
(64 mm)

30.1 in2
(19419 mm2)

243 lbs.
(110 kg)

200 tons
(1779 kN)

Air or Electric
Double Acting

16"
(406 mm)

Frame: 11" x 11"
(305 x 305 mm)
Nose: 7" Dia.
(178 mm)

8"
(203 mm)

37"
(940 mm)

4"
(102 mm)

40.45 in2
(26097 mm2)

455 lbs.
(203 kg)

T8Z-18 Hydraulic Torque Wrench Hydraulic Torque Wrench
The hydraulic torque wrench is used for tensioning anchors in tight fitting locations where it would be difficult to use an hydraulic jack. The wrench is also recommended for use when setting the large diameter Spin-Lock anchors. The torque wrenches are light weight and can achieve a maximum of 8,000 ft-lbs. Torque Tensioning charts Williams products can be found here.
Maximum
Torque
Length Height Weight
5,590 ft./lbs.
(773 kg/M)
11.11"
(279 mm)
4.49"
(114 kg)
16.75 lbs.
(7.6 kg)
8,000 ft.lbs.
(1,006 kg/M)
12.57"
(319 kg)
5.09"
(129 kg)
24.95 lbs.
(11.3 kg)
T8Z Torque Wrench

For applying torque to the anchor bolt when setting the anchor. Torque Tensioning charts Williams products can be found here.

Bolt
Diameter
Square
Drive Size
Capacity
(ft. lbs.)
*1/2"-1" 3/4" 0-500
1/2"-1" 3/4" 0-600
*1-1/8"-2" 1" 0-1,000
*Available with Ratchet Adapter
Torque Wrench
T8Z-04 Torque Multiplier (4:1)

For use with T8Z Torque Wrench. Other sizes available.

Torque Multiplier
Size Square Drive
Input
Square Drive
Output
Maximum
Torque
GA 186 1" 1-1/2" 4,000 (ft. lbs.)
T1Z & T2Z Long Fitting Tool Adapters

For driving hex nuts and setting tools, typically with our Spin-Lock anchor systems. Works with torque wrench or impact gun.
Available with 1" or 1-1/2" square drive. Please specify square drive for compatibility with your equipment.

Long Fitting Tool Adapter - Regular Socket
T2Z Regular Socket
Long Fitting Tool Adapter - Deep Socket
T1Z Deep Socket
K3F-26 Long Fitting Wrench Adapter

For applying torque to recessed anchor nuts that are under tension when using hydraulic jacks. Available in all anchor sizes.

Long Fitting Wrench Adapter
Williams Form Engineering Corp.
Post Tension
Information
Parts &
Accessories
Post Tension
Installation
Installation Equipment Case
Histories
Corrosion
Protection
Contact Us Home
Williams Form Engineering Corp. All rights reserved.